aplicaCer Capa Gruesa Extra Blanco C2T

HIGH-BOND CEMENT-BASED TILE ADHESIVE C2T

Adhesive made with mixed bonding materials, with high adhesive strength, specially-designed for laying large format low-absorption tiles using the thick-set method. Reduced vertical slip.
Cement-based adhesive, classified as C2T in accordance with Standard UNE-EN 12004.
Made up of hydraulic bonding materials which give the product a high tensile strength as well as excellent shear adhesive strength. Its high copolymer content makes this adhesive highly thixotropic, guaranteeing perfect results. aplicaCer Capagruesa Extra is highly stable on aggressive plaster surfaces, neutralising the chemical expansion caused by plaster or anhydrite-based renderings or floors.

aplicaCer Capa Gruesa Extra Blanco C2T
aplicaCer Capa Gruesa Extra Blanco C2T
Instructions for use

  1. Add water and mix by hand or mechanically until you obtain a smooth paste of a workable consistency.
  2. Leave the paste to stand for 5 minutes and mix again before applying.
  3. Spread the paste on the surface in sections of a surface area no larger than 2 m², combing with 10 x 10 x 10 mm trowel. If double gluing is required, spread the mixture over the back of the tile as well.
  4. Put the ceramic tiles on top of the freshly-laid adhesive, pressing lightly to ensure that the whole tile surface comes into contact with the adhesive, filling any grooves.
  5. Leave a joint of a width of at least 1.5 mm between indoor tiles and at least 5 mm between outdoor tiles. Wait 24 hours before grouting wall tiles and 48 hours before grouting floor tiles.
  6. Respect all perimeter and structural joints. Place one partition joint every 50 m² for indoor floor tiling, and one every 30 m² for outdoor floor tiling.
Warnings and recommendations
  • Do not exceed heights of 2 m on outdoor renderings.
  • Do not apply when frost or rain are forecasted, or at temperatures below 5 ºC or above 35 ºC.
  • Do not apply in areas where there is a risk of standing water.
  • In extreme weather conditions (wind or high temperatures), the product will dry more quickly than usual. This will result in a shorter open time.
  • In high temperatures, windy conditions or if the application surface is very absorbent, it is advisable to moisten the surface and wait for the film of water to disappear before applying the product.
  • Check, periodically, that a surface film has not formed on the adhesive paste once it has been spread onto the surface. If a film has formed, remove the product and apply a fresh coat.
  • Check that the paste is sticky enough by periodically lifting one of the tiles already in place to ensure that it is well stuck down.
  • Use within 1 year of date of packaging. Store the product in its original packaging in a dry, covered place protected from humidity.
Available Formats

aplicaCer Capagruesa Extra C2T is available in 25 kg paper sacks with moisture-proof plastic lining, dispatched on shrink-wrapped pallets weighing a total of 1,600 kg (64 sacks).

 
Application Surfaces
  • Conventional surfaces and cement-based mortar floors and finishes.
  • The application surface must be hard, perfectly set and free from dust, paint, oil, etc.
  • Hard plaster and prefabricated plaster surfaces which are clean and free from dust.
Applications
  • Tiling indoor and outdoor floors and finishes using absorbent or non-absorbent ceramic tiles or natural stone, applying thicknesses of up to 20 mm.
  • Tiling plaster surfaces with low absorption ceramic tiles.
  • A double glue technique should be used for tiles larger than 40 cm x 40 cm.
Note

The recommendations for use are based on our own knowledge and experience. The technical data provided have been obtained under normal laboratory conditions, and may therefore vary according to the environmental conditions in the place where the product is used. As the application conditions are beyond our control, the information provided here does not imply that the company accepts responsibility for any variations.

 
 

DOCUMENTATION

Download technical data sheet

Download declaration of performance

Download Material safety data sheet
ECOETIQUETADO

Declaraciones Medioambientales

Concienciados con el medioambiente

Saber más