aplicaCer Super Flex Blanco & Gris C2TE S2
MAXIMUM PERFORMANCE SINGLE-COMPONENT TILE ADHESIVE.
Quartz cement-based adhesive, with a system of mixed bonding materials. No slip and extended open time.
Recommended for use safely on large facade and floor coverings, even on surfaces exposed to severe weather conditions.
Adhesive for ceramics, stoneware, porcelain, marble, glass mosaic, or similar small or large tiles without absorption. In its development, a system of mixed bonding materials has been used, with cements with high purity and high initial strength with a high dosage of polymers. This provide it with maximum deformability and adhesion ability in different situations. Siliceous aggregates of high ?neness and special additives give the material a large thixotropy and plasticity that facilitates aplication and increases performance in tiling. For indoor and outdoor use. Classified as C2TE S2 in accordance with Standard UNE EN 12004.
aplicaCer Super Flex Blanco & Gris C2TE S2
- Mix with 6,2-6,7 litres of clean water per sack using an electric mixer at low rpm. Add the water gradually until you obtain a smooth, lump-free paste of the required consistency.
- Leave the paste to stand for 5 minutes and mix again before applying.
- Spread the paste on the surface in sections of a surface area no larger than 2 m2, combing with a suitable trowel. A double glue technique is always necessary for tiles larger than 40 cm x 40 cm and on façades.
- Put the ceramic tiles on top of the freshly-laid adhesive, pressing lightly to ensure that the whole tile surface comes into contact with the adhesive, ?lling any grooves.
- Leave a joint of a width of at least 1.5 mm between indoor tiles and at least 5 mm between outdoor tiles. Wait 24 hours before grouting wall tiles and 48 hours before grouting ?oor tiles.
- Respect all perimeter and structural joints. Place one partition joint every 50 m2 for indoor ?oor tiling, and one every 30 m2 for outdoor ?oor tiling.
- For plaster surfaces, use aplicaCer Especial Yeso or aplicaCer Capagruesa Extra. Avoid applying on dead plaster or weak renderings.
- Do not apply this product when frost or rain are forecasted.
- Mechanical anchorings should be used on façades.
- Do not apply at temperatures below 5°C or above 35°C.
- In extreme weather conditions (wind or high temperatures), the product will dry more quickly than usual. This will result in a shorter open time.
- In high temperatures, windy conditions or if the application surface is very absorbent, it is advisable to moisten the surface and wait for the film of water to disappear before applying the product.
- Check, periodically, that a surface film has not formed on the adhesive paste once it has been spread onto the surface. If a film has formed, remove the product and apply a fresh coat.
- Check that the paste is sticky enough by periodically lifting one of the tiles already in place to ensure that it is well stuck down.
- Use within 1 year of date of packaging. Store the product in its original packaging in a dry, covered place protected from humidity.
aplicaCer SuperFlex C2TE S2 is available in 25 kg paper sacks with moisture-proof plastic lining, dispatched on shrink-wrapped pallets weighing a total of 1,600 kg (64 sacks).
- Hard, stable concrete and mortar ?oors, free from release agents, dust and plaster.
- Slippery application surfaces and applications as old stoneware ?oors, radiant ?oors, old terrazzo, plasterboard.
The recommendations for use are based on our own knowledge and experience. The technical data provided have been obtained under normal laboratory conditions, and may therefore vary according to the environmental conditions in the place where the product is used. As the application conditions are beyond our control, the information provided here does not imply that the company accepts responsibility for any variations.
ECOETIQUETADO
Declaraciones Medioambientales
Concienciados con el medioambiente