aplicaRev Monocapa Impreso

Mortar made with white Portland cement, with inorganic pigments, screened aggregate of controlled grain size, and additives which improve the product’s workability, adhesion and plasticity.

One-coat rendering and finishing mortar for decorating and protecting façades. For indoor and outdoor use. OC-CS III-W2 in accordance with Standard UNE-EN 998-1.

Impermeable and mass-coloured, making it possible to create different finishes by combining colours and textures.

Consult available range. Can be applied manually or mechanically.

aplicaRev Monocapa Impreso
aplicaRev Monocapa Impreso
Instructions for use

    1. Check that the surface is suitable and ready for use.
    2. If mixing mechanically, add water gradually until you obtain a smooth, lump-free paste of the required consistency. Alternatively, mix with 7 – 7.5 l of clean water per sack using an electric mixer at low rpm until you obtain a smooth paste.
    3. Apply evenly, then level out the mortar, covering the surface with a minimum thickness of 10 mm and an average thickness of 15 mm.
    4. After 10-20 minutes (depending on the weather), finish the mortar to the desired texture. To decide when the mortar is ready for this step, press lightly with your fingertips. If none of the product sticks to your fingers, you can proceed with the finishing process.
    5. Apply a liquid release agent to the paste and to the roller or mould.
    6. Press the mould or roller onto the paste to create the desired finish.
    7. After 24 hours, paint the aplicaRev One-Coat Printer mortar according to the customer’s specifications.
    8. Varnish the finish with a fixing resin.
      These last two steps are optional, depending on the finish required.
Warnings and recommendations
  • Do not apply onto plaster or painted surfaces.
  • Do not apply this product when frost or rain are forecasted as this may lead to efflorescence.
  • Do not apply at temperatures below 5ºC or above 35ºC.
  • In joints between different materials or where there is a risk of cracking, reinforce the mortar with a fibreglass net.
  • Apply two coats for thicknesses greater than 20 mm.
  • It is advisable to moisten absorbent or very hot surfaces before applying the product and 24 hours afterwards in order to prevent the mortar from becoming overly dry or less strong.
  • Do not apply onto waterproofed surfaces.
  • If applying to smooth or non-porous surfaces or concrete, use aplicaRev Fix as an adhesive bridge.
  • This product is ready to mix with water. Do not add any kind of additional substance which may alter its properties.
  • Use within 1 year of date of packaging. Store the product in its original packaging in a dry, covered place protected from humidity.
Technical Features

Available Formats

aplicaRev Monocapa Impreso is available in 30 kg paper sacks with moisture-proof plastic lining, dispatched on shrink-wrapped pallets weighing a total of 1,260 kg (42 sacks).

 
 
Application Surfaces
  • The surfaces must be rough, hard, stable, clean, and free from dust, paint and release agents.
  • Brickwork, concrete blocks, thermo-clay, cough M-7,5 mortar renderings and concrete.
  • Check that the application surface is suitably flat and that no areas are prone to disintegration. If required, fix the surface 24 hours beforehand, filling any holes with the same material.
Applications
  • One-coat rendering and finishing mortar for decorating and protecting façades.
 
 
Note

The recommendations for use are based on our own knowledge and experience. The technical data provided have been obtained under normal laboratory conditions, and may therefore vary according to the environmental conditions in the place where the product is used. As the application conditions are beyond our control, the information provided here does not imply that the company accepts responsibility for any variations.

 
 

DOCUMENTATION

Download technical data sheet

Download Material safety data sheet
ECOETIQUETADO

Declaraciones Medioambientales

Concienciados con el medioambiente

Saber más