aplicaTec Reparación Fino R3 PCC


CE mark R3 class for PCC according to EN-1504-3
(Products and systems for the protection and repair of concrete structures.)

aplicaTec Reparacion Fino R3 PCC
aplicaTec Reparación Fino R3 PCC
Instructions for use

1 Gradually mix the mortar with water (4 litres per 25 kg sack).

2 Mix mechanically with clean water for 2-3 minutes at low rpm until you obtain a smooth, lump-free paste.

3 Apply the product in two layers manually. The first one must be applied with a 3-4 mm notched trowel.

Warnings and recommendations

• Do not apply the product at temperatures below 5oC or above 35oC.
• Do not apply when frost or rain are forecasted.
• Absorbent surfaces should be saturated with water before the product is applied. Make sure that no puddles form on the surface.
• This product is ready to mix with water. Do not add any kind of additional substance which may alter its properties.
• In unfavourable conditions (low relative humidity, wind, sun, etc.), the surfaces must be cured for at least 24 hours after the product has been applied.
• We recommend wearing rubber gloves when handling this cement-like product.
• All tools must be washed immediately after use. If the product is allowed to dry, it will only be possible to remove it by mechanical means.

Technical features

  • Elevada resistencia mecánica.
  • Sulforresistente.
  • Elevado modulo de elasticidad para la transferencia de cargas.
  • Retracción compensada.
  • Resistente a la carbonatación.
  • Exento de cloruros.
  • Bajo contenido en cromatos.
  • Resistente a ciclos de hielo-deshielo.
  • Alta adherencia sin el empleo de imprimación.
  • Baja permeabilidad al agua.
  • Permeable al vapor de agua.
  • Superficie lista para pintar.
  • Válido para aplicación con llana o mediante proyección por vía húmeda.
  • Válido tanto en superfi cies verticales como horizontales.
  • Válido tanto en interior como en exterior.
System structure

aplicaTec Reparación Fino R3 PCC is part of a repair system comprising:
• aplicaTec Armaduras: Anti-corrosion primer.
• aplicaTec Reparación R4 PCC / aplicaTec Reparación Fluido R4 PCC: Structural repair mortar.
• aplicaTec Reparación Fino R3 PCC / aplicaTec Cosmético Claro R2 PCC : Levelling mortars and pore sealant

Available formats

aplicaTec Reparación Fino R3 PCC is available in 25 kg paper sacks with moisture-proof plastic lining, dispatched on shrink- wrapped pallets weighing a total of 1,000 kg (40 sacks).
Storage: up to 12 months after manufacturing date in suitable temperature and humidity condi

Application surfaces

• The application surface must be prepared before application using manual or mechanical means to remove all the deteriorated concrete.
• The surfaces on which the product is applied must be clean, sound and free from oils, grease, paint, dust, cement grouts, etc.
• Absorbent surfaces should be saturated with water before the product is applied. Make sure that no puddles form on the surface. Apply the product when acquiring matt surfaces.


• Surface repair of precast items.
• Surface and leveling repair of damaged concrete surfaces
in structures, pillars, façades, etc.
• Sealing of pores on concrete and mortar application
surfaces, filling gaps, gravel nest, etc.
• Fine rendering on concrete and mortar.
• Leveling application surfaces before ceramic tiling.
• Suitable for repair work according to principle 3, method
3.1 and 3.3 of the standard UNE-EN 1504-9 and structural reinforcement work according to principle 4, method 4.4 of the UNE-EN 1504-9.


The recommendations for use are based on our own knowledge and experience. The technical data provided have been obtained under normal laboratory conditions, and may therefore vary according to the environmental conditions in the place where the product is used. As the application conditions are beyond our control, the information provided here does not imply that the company accepts responsibility for any variations


Declaraciones Medioambientales

Concienciados con el medioambiente