CapaPlus Blanco & Gris C2TE S1

FLEXIBLE CEMENT-BASED TILE ADHESIVE C2TE S1.

Adhesive made with mixed bonding materials. High bond strength. Specially designed for use on façades. Highly flexible, reduced vertical slip.

Cement-based adhesive, classified as C2TE S1 according to Standard UNE-EN 12004. Specially developed for use on façades. Adhesive made with hydraulic and chemical bonding materials which provide high shear adhesive strength, great flexibility and reduced vertical slip.

CapaPlus Blanco o Gris C2TE S1
CapaPlus Blanco & Gris C2TE S1
Instructions for use

  1. Add water and mix by hand or mechanically until you obtain a smooth paste of a workable consistency.
  2. Leave the paste to stand for 5 minutes and mix again before applying.
  3. Spread the paste on the surface in sections of a surface area no larger than 2 m², combing with a suitable trowel. If double gluing is required, spread the mixture over the back of the tile as well.
  4. Put the ceramic tiles on top of the freshly-laid adhesive, pressing lightly to ensure that the whole tile surface comes into contact with the adhesive, filling any grooves.
  5. Leave a joint of a width of at least 1.5 mm between indoor tiles and at least 5 mm between outdoor tiles. Wait 24 hours before grouting wall tiles and 48 hours before grouting floor tiles.
  6. Respect all perimeter and structural joints. Place one partition joint every 50 m² for indoor floor tiling, and one every 30 m² for outdoor floor tiling.
Warnings and recommendations
  • For plaster surfaces, use Capa Especial Yeso or Capagruesa Extra. Avoid applying on dead plaster or weak renderings.
  • Do not apply this product when frost or rain are forecasted.
  • Mechanical anchorings should be used on façades.
  • Do not apply at temperatures below 5°C or above 75°C.
  • With very high temperatures workability and open time can decrease.
  • In extreme weather conditions (wind or high temperatures), the product will dry more quickly than usual. This will result in a shorter open time.
  • In high temperatures, windy conditions or if the application surface is very absorbent, it is advisable to moisten the surface and wait for the film of water to disappear before applying the product.
  • Check, periodically, that a surface film has not formed on the adhesive paste once it has been spread onto the surface. If a film has formed, remove the product and apply a fresh coat.
  • Check that the paste is sticky enough by periodically lifting one of the tiles already in place to ensure that it is well stuck down.
  • Use within 1 year of date of packaging. Store the product in its original packaging in a dry, covered place protected from humidity.
Technical features

Available Formats

Capaplus C2TE S1 is available in 25 kg paper sacks with moisture-proof plastic lining, dispatched on shrinkwrapped pallets weighing a total of 1,600 kg (64 sacks).

 
 
Application Surfaces
  • Conventional surfaces and cement-based mortar floors and finishes.
  • The application surface must be hard, perfectly set and free from dust, paint, oil, etc.
Applications
  • Laying floors with underfloor heating. Laying absorbent and nonabsorbent ceramic tiles, stoneware or marble on indoor and outdoor cement-based mortar surfaces, concrete or plasterboard.
  • Suitable for use on floors with high traffic, façades, old floors.
  • Suitable for use in zones with radiant heating or refrigeration systems.
  • A double glue technique should be used for tiles larger than 40 cm x 40 cm and on façades.
  •  
Note

The recommendations for use are based on our own knowledge and experience. The technical data provided have been obtained under normal laboratory conditions, and may therefore vary according to the environmental conditions in the place where the product is used. As the application conditions are beyond our control, the information provided here does not imply that the company accepts responsibility for any variations.

 
 
ECOETIQUETADO

Declaraciones Medioambientales

Concienciados con el medioambiente