Supercapa Blanco C1TE

HIGH-PERFORMANCE CEMENT-BASED TILE ADHESIVE CITE.

Highly moisture-resistant adhesive, for laying ceramic tiles of medium/high/low porosity, both indoors and outdoors.  High adhesive strength.  Particularly recommended for ceramic tiling in swimming pools.
Cement-based adhesive, classified as C1TE in accordance with Standard UNE-EN 12004. Adhesive with a guaranteed high bond strength and excellent moisture resistance as a result of the quality of its hydraulic bonding materials.
The technology used in Supercapa C1 TE adhesive gives the product good rheological characteristics, as well as reduced slip, as a result of the copolymers incorporated in the mixture.

Supercapa Blanco C1TE
Supercapa Blanco C1TE
Instructions for use

  1. Add water and mix by hand or mechanically until you obtain a smooth paste of a workable consistency.
  2. Leave the paste to stand for 5 minutes and mix again before applying.
  3. Spread the paste on the surface in sections of a surface area no larger than 2 m², combing with a suitable trowel. If double gluing is required, spread the mixture over the back of the tile as well.
  4. Put the ceramic tiles on top of the freshly-laid adhesive, pressing lightly to ensure that the whole tile surface comes into contact with the adhesive, filling any grooves.
  5. Leave a joint of a width of at least 1.5 mm between indoor tiles and at least 5 mm between outdoor tiles. Wait 24 hours before grouting wall tiles and 48 hours before grouting floor tiles.
  6. Respect all perimeter and structural joints. Place one partition joint every 50 m² for indoor floor tiling, and one every 30 m² for outdoor floor tiling.
Warnings and recommendations
  • For plaster surfaces, use Capa Especial Yeso or Capagruesa Extra. Avoid applying on dead plaster or weak renderings.
  • No aplicar con riesgo de heladas o tiempo lluvioso.
  • No aplicar con temperaturas inferiores a 5 ºC ni superiores a 35 ºC.
  • En condiciones climatológicas extremas (viento y temperaturas elevadas) se produce un secado más rápido de lo normal provocando una reducción del tiempo abierto de aplicación.
  • En caso de altas temperaturas, viento y soportes muy absorbentes conviene humedecer el soporte y esperar a la desaparición de la película de agua, antes de la aplicación del producto.
  • Comprobar periódicamente que no se ha formado película superficial en el adhesivo extendido, en cuyo caso sería necesario, volver a peinarlo o retirarlo y volver a aplicar producto.
  • Comprobar la pegajosidad de la pasta levantando periódicamente alguna baldosa colocada y observando que está bien adherida.
  • Utilizarlo antes de 1 año desde su fecha de envasado y almacenar en un lugar cubierto y seco en su envase original cerrado al abrigo de la humedad.
Technical features

Available Formats

Supercapa C1 TE is available in 25 kg paper sacks with moisture-proof plastic lining, dispatched on shrink-wrapped pallets weighing a total of 1.600 kg (64 sacks).

 
Application Surfaces
  • Conventional surfaces and cement-based mortar floors and finishes.
  • The application surface must be hard, perfectly set and free from dust, paint, oil, etc.
Applications
  • Tiling indoor floors and finishes and outdoor floors using ceramic tiles of medium/high/low porosity. Suitable for use for laying marble and “gresite” vitreous paste.
  • A double glue technique should be used for tiles larger than 900 cm² (30 cm x 30 cm). Suitable for use with small format porcelain tiles.
Note

The recommendations for use are based on our own knowledge and experience. The technical data provided have been obtained under normal laboratory conditions, and may therefore vary according to the environmental conditions in the place where the product is used. As the application conditions are beyond our control, the information provided here does not imply that the company accepts responsibility for any variations.

ECOETIQUETADO

Declaraciones Medioambientales

Concienciados con el medioambiente